Fanuc ge manual

Embed Size px x x x x The descriptions and specifications contained in this manual were ineffect at the time this manual was approved for printing. Approved trainingnecessitates that the courses selected be relevant to the type ofsystem installed and application performed at the customer site. WARNINGThis equipment generates, uses, and can radiate radiofrequency energy and if not installed and used in accordancewith the instruction manual, may cause interference to radiocommunications.

As temporarily permitted by regulation, ithas not been tested for compliance with the limits for Class Acomputing devices pursuant to subpart J of Part 15 of FCCRules, which are designed to provide reasonable protectionagainst such interference.

Operation of the equipment in aresidential area is likely to cause interference, in which casethe user, at his own expense, will be required to takewhatever measure may be required to correct theinterference.

For additional information contact. Training Department W. Hamlin RoadRochester Hills, Michigan www. All Rights ReservedThe information illustrated or contained herein is not to bereproduced, copied, downloaded, translated into another language,published in any physical or electronic format, including internet, ortransmitted in whole or in part in any way without the prior writtenconsent of FANUC Robotics America, Inc. No part of this manual may be reproduced in any form.

All specifications and designs are subject to change without notice. This manual includes information essential to the safety ofpersonnel, equipment, software, and data. This information isindicated by headings and boxes in the text.

Consult your GE Fanuc sales representative or field service office for help in identifying local specialists. The built-in Station Manager software provides on-line supervisory access to the Ethernet Interface, through either Serial Port 1 or over the Ethernet cable.

The Station Manager services on the Ethernet Interface include:. H An interactive set of commands for interrogating and controlling the station. H Unrestricted access to observe internal statistics, an exception log, and configuration parameters.

H Password security for commands that change station parameters or operation. Access to the Station Manager is attained through a user-provided computer terminal or terminal emulator. This utility is supplied with any updates to the Ethernet Interface software. There are only a few simple tasks required to get your Ethernet Communications System working. These tasks are addressed in detail later in this manual. Install the Ethernet Interface into the Series baseplate and connect it to the network.

The table below breaks down the tasks shown in Figure and identifies where in the manual they are described. This chapter describes the basic features of the Ethernet Interface, its installation, configuration, and a procedure for its initial checkout on your Ethernet cable. The chapter first provides a hardware overview of the Ethernet Interface.

It is then divided into four Installation Procedures, each providing an overview of the procedure and then explaining the detailed steps to be performed. As you work through a procedure you may encounter references to the appendices and other chapters in this manual. These references provide more detailed information about the subject under discussion.

Some of the procedures require prior Ethernet cable plant design and installation. By completing the Installation Procedures you will gain an understanding of the parts of the network and how they fit together. You will also have confidence that your equipment is working properly.

It is connected to an Ethernet network via a user-provided transceiver cable and transceiver. The following figure shows the layout of the Ethernet Interface. Four LEDs are located at the top of the board.

The Restart button is located immediately below the LEDs. Remove the front cover to access them. This permits the operator to verify that all LEDs are operational. These four functions behave similarly in all states except for the Software Load state. While in this state, pressing the button will cause an immediate restart into the Operational state if the software in the Ethernet Interface has not been corrupted or erased.

If the software has been corrupted or erased, pressing the button will cause an immediate restart back into the Software Load state.

The following text describes Restart button behavior while not in the Software Load state. Then the Interface performs either a restart, a restart and enter Software Load state, or a restart and enter Maintenance state, depending on the duration that the operator depresses Restart. Restart: Pressing the Restart button momentarily less than 5 seconds requests a restart of the Ethernet Interface. When the Restart button is pressed, all LEDs go out. When it is released, all LEDs flash ON, then power-up diagnostics run, and the software on the Interface is restarted into the Operational state.

Restart and Enter Software Load State: Pressing and holding the Restart button for between 5 and 10 seconds forces a restart and requests entrance to the Software Load state. A reload is used to install a software update into the module and is not part of normal operation.

The PC Software Loader is a separate software utility which updates the communications software in the Ethernet Interface. See Appendix E for more information. At any time before you initiate a load with the PC Software Loader, you can restart the Ethernet Interface by pressing the Restart button. Pressing this button will immediately cause the board to restart. If the reload has been initiated, see Appendix E for more information. Restart and Enter Maintenance State: Pressing and holding the Restart button for more than 10 seconds forces a restart and requests entrance to the Maintenance state.

Maintenance state must be invoked to change Advanced Parameters. While in Maintenance state, all Advanced Parameters revert to their default value. In any case, any data being transferred by the Ethernet Interface at the time of the Restart will be lost.

The Restart button is not operable during the diagnostic phase of power-up. There are two serial ports on the Ethernet Interface: the Station Manager port port 1 and the Software Loader port port 2.

Series Programmable Controller Installation Manual. In addition to the Ethernet Interface, make sure you have the items listed below before you begin.

H An operating Logicmaster t system release 6. See Appendix B for more information. H A terminal or IBM-compatible personal computer equipped with terminal emulation software. Use the following instructions as a guide when inserting a module into a slot in a baseplate. These instructions assume that the power suppy on the baseplate is to your left.

Do not insert or remove modules with power applied. This could cause the PLC to Stop, damage the module, or result in personal injury. Align the module with the desired base slot and connector. Tilt the module upwards so that the top rear hook of the module engages the slot on baseplate.

Swing the module downward until the connectors mate and the lock-lever on the bottom of the module snaps into place engaging the baseplate notch. Visually inspect the module to be sure that it is properly seated.

Remove the front cover of the Interface. Secure the cable. The other end of the transceiver cable should be connected to an external IEEE If the transceiver has a switch or jumper for SQE, it must be enabled.

Note: The transceiver cable may be built-in to the transceiver or removable. Replace the front cover and restore power to the baseplate. Continue with Procedure 2: Configuring the Ethernet Interface. An Ethernet Interface can be mounted on a CPU baseplate, an expansion baseplate, or a remote baseplate. However, due to power requirements, only two Ethernet Interfaces are permitted per baseplate.

The Hand Held Programmer may not be used to configure the Interface. For the Ethernet Interface specifically, the configuration software allows you to:.

H Define the status address of the Ethernet Interface. H Configure the serial ports optional. Move the cursor to the desired rack and slot location. The slot may be either unconfigured or previously configured. Press the Communications softkey, i. Your screen display will change to the one shown on the following page. Press ethnet F2. Your screen display will change to the one shown below.

Press Enter to select the Ethernet Interface. You will then see the screen shown on the following page. Do not use the bits assigned to the LIS bits and Channel Status bits for other purposes or your data will be overwritten. It is especially important that each node on the network is assigned a unique IP address. However, if you have no network administrator and a simple isolated network with no gateways, you can use the following range of values for the assignment of local IP addresses:.

The Name Server IP address is not currently used and is reserved for future use. If the isolated network is ever connected to another network, the IP addresses3.

The IP addresses must be assigned so that they are compatible with the connected network. Refer to Appendix C for more information on addressing. Optionally, after you have assigned the IP address, etc. The defaults for both ports are shown on the previous screen. Data Rate: Data rate bits per second or bps for the port. Choices are , , ,. Parity: Type of parity to be used for the port.

Stop Bits: Enter the number of stop bits. Featured Brands. Repair Services. Engineering Services. Payment Options. Social Channels. Contact us Search field Search. Sign in Welcome Back! Sign in to view your discounts, savings, and track orders. Sign in. Not a member? Create an Account. Industrial Computers. Flat Panel Monitors. Ethernet Switches. Protocol Gateways. Serial Device Servers.

PL Series Kit. Bracket Series. Panelsphere Series. Micro OCS Series. Flat Panel Computers. Industrial Workstations.