Is your question not listed? When rotating the front wheel, the magnet's 4 center must be aligned with the sensor's 3 marking. The distance between the sensor 3 and the magnet 4 must be less than 5 mm. Current speed does not appear. First, short-circuit the contact of the main unit a few times with a piece. Battery Lithium Battery CR x 1 battery life: approx. Microcomputer 4-b it 1 -ch ip Cry stal controlled oscillator.
Tire Sizes Tire sizes of 16, 18, 20, 22, 24, 26, C, and 27 inches, or tire peripheral. Ask a question. The main unit may still have a charge. Put the battery in backwards to short the unit then install properly and do all clear operation.
Incorrect data appears. Current speed does not appear. First, short-circuit the contact of the main unit a few times with a piece. If current speed appears, the main unit is working fine and the cause should be attributed to the. Is the clearance between the sensor and the magnet too large? Are the magnet's center and the sensor's marking line aligned? Re-adjust the positions of the magnet and the sensor.
The clearance should be less than 5. Even if the outside of the cord looks normal, there could be damage. Replace the bracket and sensor set with a new one. Is there anything sticking on the contact of the main unit or the bracket? Current speed disappears when using in the rain. Wipe any water or dirt from the contacts and apply a water repellent silicon grease. Do not. If the screen becomes dim, it is the time to replace the battery. After replacing the battery, perform the all-clear operation.
No measurement is done on the VELO5. The unit starts measuring automatically when you start pedaling, and stops measuring when your come. The upper display always shows the Current Speed.
Each time you press the MODE button, a different data value appears on the lower line. If the main unit does not receive a signal after about 10 minutes, the main unit enters Power Saving. Mode and displays the clock count only. To re turn to normal display, press the MODE button or start. MODE button and the measured data will return to zero. However, the Odometer total distance and. In the clock mode, press SET button on the back, and the display enters clock setting mode.
If mph has been selected, it becomes hour clock. You can select a tire. If they become rusty, it will. Put the battery in backwards to short the unit then install properly and do all clear operation. Current speed does not appear. First, short-circuit the contact of the main unit a few times with a piece.
If current speed appears, the main unit is working fine and the cause should be attributed to the. Is the clearance between the sensor and the magnet too large? Are the magnet's center and the sensor's marking line aligned? Re-adjust the positions of the magnet and the sensor. The clearance should be less than 5. Even if the outside of the cord looks normal, there could be damage. Replace the bracket and sensor set with a new one. Is there anything sticking on the contact of the main unit or the bracket?
Current speed disappears when using in the rain. Wipe any water or dirt from the contacts and apply a water repellent silicon grease. Do not. E is displayed and calculation ceases. If "Mile" is selected for scale symbol, the clock time is in 12 -hour. If "Km", the clock. When the main unit does not receive a signal, or a button has not been pressed for. By pressing the Main button, or by receiving signal, this function is re-. Do "All Clear" operation.
If possible, write down the Odo data before all clear operation, and. Current speed does not appear. When current speed does not appear, first short-circuit the. Is there anything on the contact of the main unit or of the bracket? Is the distance between the sensor and the magnet too far? Are the marking line of the sensor and the center of magnet aligned?
Adjust the position of the sensor and magnet again. Current speed does not appear in wet condition. Wipe the contacts with dry cloth. Contacts can also be treated with a water repellent silicon. Do not use industrial water repellent; it. When "Mile" was chosen for speed scale,. In order to continue accumulation of Odo data, write down the stored.
Odo data before replacing the battery. Insert a new lithium battery.
0コメント